Welcome to Structure Tech

There’s No Perfect Temperature For Your Water Heater

By In Water Heater Temperature On April 17, 2012


What’s the best temperature to set your water heater to?  There’s no single great answer.  The American Society of Sanitary Engineering Scald Awareness Task Group recently released a white paper on this topic, which essentially says that there is no perfect temperature to set you water heater to.

What’s a safe temperature for water?

On the side of most water heaters you’ll find a warning that says water temperatures of 125 degrees Fahrenheit can cause burns or death.  To be safe, the water coming out of the plumbing fixtures in a home shouldn’t be any hotter than 120 degrees.   The handy photo below (courtesy of Charles Buell)  shows how fast second and third degree burns can happen at temperatures that any new water heater is capable of producing.

Water Temperatures

Just turning down the temperature at your water heater until you’re at a safe 120 degrees isn’t enough to solve potential scald hazards because the thermostat on a water heater isn’t designed to keep the water at a constant temperature; it’s just designed to keep the water within a certain range of temperatures.  Seattle home inspector Charles Buell has posted a couple different blogs explaining how this works – one explaining how water heaters sometimes run out of hot water faster than they should, and another on the different temperatures that will be produced by a water heater during different stages of the heating cycle.

During a recent inspection of a large home that was heated with two high-efficiency water heaters, I found quite a range in temperatures.  When I first turned the hot water on at a fixture, the water temperature started out cool; this was because the water in the hot water pipe had cooled down to room temperature.  As the hot water from the top of the tank arrived at the plumbing fixtures, the water temperature rapidly jumped up to nearly 154 degrees – this was hot enough to cause first degree burns instantaneously, and second degree burns within one second.

Dangerously hot water

The water only stayed at this temperature for a few seconds; it quickly dropped back down to about 135.  While there was a tempering valve installed to mix cold water in with the hot water right at the water heater outlet, it wasn’t enough to completely control the water temperature at the fixtures.

Minnesota has no requirements for residential water temperatures.  Anti-scald devices are required in all new or remodeled showers or shower-bath combos in Minnesota (4715.1380 Subp. 5), but this does nothing to address the final temperature of the water coming out of a fixture.   Anti-scald devices only help to prevent people from getting scalded by a sudden swing in temperature while taking a shower.  With old shower valves that didn’t have the anti-scald feature, if a toilet would flush while someone was taking a shower the pressure on the cold water line would drop, quickly increasing the water temperature at the shower.

Lower Temperatures Allow Bacteria Growth

It seems as though the solution to help prevent accidental scalding would be to turn down the temperature at the water heater to say, 115 degrees, but lower temperatures actually create other problems.

At temperatures below 135 to 140, Legionellae bacteria, which is responsible for Legionnaires’ Disease, can survive and even multiply in the water heater tank.  Estimates by LegionellaPrevention.org say that up to 600,000 cases of Legionnaires’ Disease are misdiagnosed as pnemonia each year, because this is something that isn’t tested for in hospitals.   The diagram below shows the time it takes to kill Legionellae Bacteria at different temperatures.

To help prevent bacteria growth, the ASSE recommends keeping the water in your water heater tank at about 135 – 140 degrees Fahrenheit.

Water Temp Effects on Legionellae

Of course, this creates a scalding hazard.

So What’s the Answer?

To help prevent bacteria growth and to lower the risk of scalding, have a plumber install a tempering valve and crank up the temperature at your water heater to about 135 – 140, as ASSE recommends.  Last year I wrote about how I installed a tempering valve on the hot water outlet at my own house in order to get more water out of my water heater.  These valves would be a good thing to install in every home.  A tempering valve allows you to keep the water at a dangerously high, Legionellae-killing-temperature inside the water heater tank, yet it mixes cold water in with the hot water right at the outlet, making it so you don’t get this hot water at the rest of the fixtures in your home.

Tempering valve function

As I mentioned in my story about the recent inspection with dangerously hot water, a tempering valve won’t guarantee safe water temperatures, but it will get you a lot closer.

Reuben Saltzman, Structure Tech Home Inspections – Email – Minnesota Home Inspector

        


About the Author

Reuben

Reuben is a second generation home inspector with a passion for his work. He grew up remodeling homes and learning about carpentry since he was old enough to hold a hammer. Reuben has worked for Structure Tech since it was purchased by Neil in 1997, and is now co-owner of the company. Reuben’s favorite customers are the ones who have a lot of questions; he grew up thinking he was going to be a school teacher because he enjoyed teaching others so much. In a sense, that’s a lot of what home inspections are about, so Reuben truly does what he loves. Reuben has an A.A. degree in liberal arts and has attended most of the Building Inspection Technology classes at North Hennepin Community College. Reuben and his wife are the proud parents of two young childen, Cy Alexander and Lucy Nicole, and have a German Shepherd named Stanley. With two young children Reuben doesn’t have much free time, but he still tries to play disc golf as often as possible during the summer. Reuben lives in Maple Grove, MN. Professional Qualifications / Memberships: *ASHI Certified Inspector *President, ASHI Heartland Chapter *Member, Minnesota Society of Housing Inspectors (MSHI) *Licensed Minneapolis Truth-in-Sale of Housing Evaluator *Licensed Saint Paul Truth-in-Sale of Housing Evaluator *Licensed Maplewood Truth-in-Sale of Housing Evaluator *Licensed Hopkins Truth-in-Housing Evaluator *Licensed Robbinsdale Point of Sale Evaluator *Affiliate Member, Southern Twin Cities Association of Realtors

Related Posts

2 Comments

  • Greg Blouch 2 YEARS AGO

    Settings? Electric hot water overheated and kicked the lower element breaker twice (reset - and tripped again). Replaced the lower thermostat - which was similar, but not identical to the original. Now, I seem to have lost recovery. Through the course of a shower, need to reduce the amount of cold water in order to maintain temp. Cheap tester says the components are working. I have tweaked temperature settings - but no luck correcting the problem. Suggestions?

  • TPM 2 YEARS AGO

    Thanks-just the info I was looking for. Very informative!