Find water damage hiding behind the siding.
Stucco homes in Minnesota, especially those built since the 1980s, have a history of failing from water intrusion. Moisture testing finds it before it becomes an expensive repair.
Exterior probe testing.
We drill small 3/16” holes into the stucco at strategic spots and insert moisture probes to measure what’s happening behind it. We’ve done this since the late 1990s and know of no better method.
Measures moisture directly
Probes read the moisture content inside the wall, so we can tell whether water has gotten behind the exterior.
Tests the critical spots
The areas most likely to fail can only be reached from outside, which is why we prefer exterior testing.
A detailed report
You get a report showing where we tested and what we found. See the sample below.
Water problems cost more with stucco.
Every type of siding can have water problems, but stucco failures tend to be more extensive and more expensive to repair.
- It’s not just Woodbury. The City of Woodbury openly discussed the issue in its stucco position paper (first published in 2003, last updated in 2011), but the problem is widespread across Minnesota.
- Damage stays hidden. Water can saturate the wall behind stucco long before anything shows on the surface.
- Early detection pays. Catching water intrusion early keeps repair costs down.
Why we don’t rely on other approaches.
Interior probe testing
We offer it, but it’s limited. We can’t drill into tile, wood paneling or other finishes, and the most critical areas can’t be reached from inside.
Cutting it open
It will tell you whether there’s a problem, but it’s expensive and unsightly. Even with no problem, you’re left with patched cut marks.
Borescope or video scope
Insulated walls make this very difficult, and a camera can’t detect moisture. Wood can look fine and still be saturated. We don’t recommend it.
Infrared cameras seemed promising when they became affordable, but thermal imaging has proven inconclusive for stucco. A cool spot doesn’t mean water reached the sheathing, and we’re not aware of any reputable company in Minnesota offering it.
We test all kinds of siding.
Stucco
Pin-probe testing of stucco houses is our bread and butter. We prefer exterior testing, but can test from the interior too.
Stone
Stone siding (masonry veneer) is nearly identical to stucco and gets the same pin-probe testing.
Brick
Brick siding can be tested with pin probes.
Vinyl
We offer non-invasive moisture testing on vinyl siding.
Wood
Non-invasive surface scanning, followed by pin-probe testing at suspect areas.
Composite
James Hardie or LP SmartSide siding is tested like wood: non-invasive scanning, then probes where needed.
Aluminum and steel siding can be pin-probe tested from the interior only.
Buying or own a stucco home?
Find out what’s behind the walls before water damage turns into a major repair.
Stucco and Moisture Testing FAQs
Quick answers from the Structure Tech team. Don’t see your question? Call (952) 915-6466.
What does moisture testing tell me?
Moisture testing tells you whether water is getting in behind the exterior cladding.
It can find problems you’d never see from the surface and show where a closer look is needed.
Why are newer stucco homes a concern?
A lot of Minnesota stucco homes built since the 1980s have had serious water-intrusion problems.
The tricky part is that hidden damage can build up behind stucco that still looks great, which is why specialized testing is often worth it.
The home I’m buying has real stucco, not synthetic. Should I still test it?
Yes, test it. Traditional “real” stucco is actually what we’ve had so many problems with here in Minnesota.
It’s not just the synthetic stuff. Reuben explains more in Problems with stucco houses in Minnesota.
How does exterior probe testing work?
We drill small 3/16-inch holes in selected spots and stick probes in to measure the moisture in the materials behind the cladding.
When we’re done, we fill the holes with caulk that matches the color of the house.
Is moisture testing included in a home inspection?
No. Invasive exterior moisture testing is separate from a standard home inspection, and it requires permission.
A visual inspection and interior moisture checks just can’t tell you what probe testing behind the cladding can.
Can I schedule moisture testing at the same time as the home inspection?
Yes. You can schedule moisture testing at the same time as your Structure Tech home inspection.
The home inspector and the moisture tech won’t get in each other’s way, and you can set it all up with one call.
Who must sign the moisture-testing agreement?
The property owner or the seller’s legal power of attorney has to sign our moisture-testing agreement before we can start.
Sorry, an amended purchase agreement won’t cut it. The seller can sign our Moisture Testing Release online.
Will the holes be visible after testing?
The holes are filled with color-matched caulk, so they’re usually only noticeable up close or to a trained eye.
We bring more than 30 shades of caulk to get a good match. If the owner wants, they can touch up the spots with paint.
Will moisture probe testing damage the house?
No. We’ve tested thousands of stucco homes over more than 20 years and have never had a single case of water damage caused by probe testing.
Probe testing is the most reliable and least intrusive way to test a stucco home.
Does probe testing compromise the moisture barrier?
Probe testing does puncture the moisture barrier, but we seal every hole by injecting caulk all the way in.
The caulk seals up the penetration once testing is done.
Why do you use caulk instead of stucco to fill the holes?
We use caulk because it’s flexible and we can inject it deep into the holes.
Trying to color-match stucco on site would be difficult and cost a fortune, so caulk is the better fix.
Are your moisture technicians certified?
Yes. Our moisture technicians, Antonio and Corey, are EDI Level 2 Certified Members with Adhered Stone Veneer Certificates.
Can an infrared camera replace probe testing?
No. An infrared camera can’t replace probe testing for moisture behind stucco.
Temperature patterns alone don’t reliably tell you whether a wall is wet. Probe testing gives you actual readings in specific spots.
Can you test siding other than stucco?
Yes. We do moisture testing on stucco, stone, vinyl, wood, brick, and metal siding.
How we test and what access we need depends on the material.
Can stucco moisture testing be performed from inside the house?
Sometimes, but finishes and access can limit how much we can test from inside.
We generally prefer to test stucco from the outside, because some of the most important spots can’t be reached from inside.
Is stone veneer tested like stucco?
Pretty much. Stone veneer can have the same kinds of water-intrusion problems as stucco.
We use pin-probe moisture testing, and figure out the specific test locations and access for each house.
Can stucco look good but have hidden moisture damage?
Yes. Good-looking stucco doesn’t mean there’s no moisture or damage behind it.
Moisture testing tells you what the surface can’t.
What if testing finds elevated moisture?
Elevated moisture readings point to areas that need a closer look for water intrusion and possible damage.
A qualified repair pro may need to figure out where the water’s coming from and how far the damage goes before recommending a repair plan.
Does a dry reading guarantee the wall has no damage?
No. A dry reading doesn’t guarantee the wall has no hidden or past damage.
Readings tell you about the spots we tested, not every square inch of the wall.
Can moisture testing be done in the rain?
No. We can’t do exterior moisture testing in the rain.
The equipment gets wet, and that makes an accurate moisture report impossible.
Can moisture testing be done right after a recent rain?
Yes. Moisture testing can be done right after it rains.
We’re probe testing the wall sheathing behind the cladding, which should always be dry.
What if it hasn’t rained for a month? Won’t the wall be dry?
Not necessarily. We can still get accurate results on stucco and stone-sided homes after a long dry spell.
Stucco homes take months to dry out, so we can do moisture testing pretty much year-round.
Can moisture testing be done during freezing weather?
We do exterior moisture testing when it’s above 32 degrees, because frozen building materials don’t give accurate readings.
If you’re setting an inspection deadline in cold weather, call us first so we can confirm whether we can do the test.
How do I prepare the property for moisture testing?
Get the signed authorization taken care of ahead of time, and make sure we can get to the areas we’re testing.
Let us know about locked gates, security systems, landscaping, or any limits on getting inside before the appointment.
Can I be there for the moisture testing?
Sure, but you’ll probably be bored. Moisture testing isn’t a learning experience the way a home inspection is.
It’s a lot of setting up ladders, drilling holes, taking readings, and filling holes, over and over. If you plan to attend, bring a book.
How much does moisture testing cost?
Our moisture testing prices are based on the size of the house. Whole-house testing starts at $845 for homes up to 3,000 total square feet, and testing a single wall is $545.
Call our office for a quote on your property.
When are you available for moisture testing?
Call our main office at 952-915-6466 for the most current moisture-testing availability.
Let us know your inspection deadline so we can fit the testing in.
When will I receive my moisture-testing report?
Most moisture-testing reports go out within 48 hours of the test.
You can see a sample report on this page. Questions about the scope for your property? Just call the office.
Do you offer a moisture warranty?
We don’t, but you can buy a moisture warranty through MoistureWarranty.com.
They accept our moisture reports as qualified moisture inspections.
Still have questions? We’re happy to help.
Schedule Your Inspectionor call (952) 915-6466 · Monday – Sunday, 8 am – 5 pm